8-String WLED Driver with Integrated Step-Up
Regulator and SMBus/PWM Dimming Capability
3) Create a ground island (PGND) consisting of the
input and output capacitor ground and negative
terminal of the current-sense resistor. Connect all
these together with short, wide traces or a small
ground plane. Maximizing the width of the power
ground traces improves efficiency and reduces out-
put voltage ripple and noise spikes. Create an analog
ground island (AGND) consisting of the overvoltage-
detection divider ground connection, the ISET and
DFSET resistor connections, the COMP resistor and
capacitor connections, and the device’s exposed
backside pad. Connect the AGND and PGND islands
by connecting the SGND pins directly to the exposed
backside pad. Make no other connections between
these separate ground planes.
Simplified Operating Circuit
4) Place the overvoltage-detection divider resistors as
close to the OVP pin as possible. The divider’s center
trace should be kept short. Placing the resistors far
away causes the sensing trace to become antennas
that can pick up switching noise. Avoid running the
sensing traces near LX.
5) Place the IN pin bypass capacitor as close to the
device as possible. The ground connection of the IN
bypass capacitor should be connected directly to
SGND pins with a wide trace.
6) Minimize the size of the LX node while keeping it wide
and short. Keep the LX node away from the feedback
node and ground. If possible, avoid running the LX
node from one side of the PCB to the other. Use DC
traces as a shield if necessary.
Refer to the MAX17105 evaluation kit for an example of
proper board layout.
Chip Information
PROCESS: BiCMOS
V CC
ISET
IN
FAULT
LX
Package Information
DFSET
PGND
OVP
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages .
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
EN
MAX17105
24 TQFN-EP
T2444-4
21-0139
OSC
COMP
SDA
SCL
FB1
FB2
FB3
10kHz
PWMI
PWM0
SGND
EP
FB4
FB5
FB6
FB7
FB8
_______________________________________________________________________________________
25
相关PDF资料
MAX17127ETP+ IC WLED DVR SIX STRING 20TQFN
MAX17149ETE+ IC LED DRVR 6CH STEP UP 16QFNEP
MAX17410EVKIT+ KIT EVAL FOR MAX17410 CTLR
MAX17605AUA+ IC MOSFET DRVR 4A DUAL 8UMAX
MAX1848ETA+T IC LED DRIVR WHITE BCKLGT 8-TDFN
MAX1912EUB+ IC LED DRVR WHITE BCKLGT 10-MSOP
MAX1916EZT+T IC LED DVR WHITE BCKLGT 6TSOT
MAX1986ETE+T IC LED DRVR WHITE BCKLGT 16-TQFN
相关代理商/技术参数
MAX17105EVKIT+ 功能描述:电源管理IC开发工具 MAX17105 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MAX17106ETN+ 功能描述:PMIC 解决方案 PMIC for LCD RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MAX17106ETN+T 功能描述:其他电源管理 Integrated Circuits (ICs) Power Management - Specialized - IC REG STEP UP/HV STEPUP 56-TQFN RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel
MAX17106EVKIT+ 制造商:Maxim Integrated Products 功能描述:STEP-UP REGULATOR HIGH-VOLTAGE STEP-UP WITH TEMPERATURE COMP - Boxed Product (Development Kits)
MAX17107ETI+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX17108ETI+ 功能描述:LCD Gamma缓冲器 10Ch Scan Driver & VCOM Amp RoHS:否 制造商:Maxim Integrated 输入补偿电压: 转换速度: 电源电压-最大:20 V 电源电压-最小:9 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-38 封装:Tube
MAX17108ETI+T 功能描述:LCD 驱动器 10Ch High-Volt & VCOM Amp RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube
MAX17108EVKIT+ 功能描述:电源管理IC开发工具 MAX17108 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V